Mooring system is the part that the owner of a yacht or boat sees the least, but on which the safety of the entire vessel depends. The anchor, chain, connections and buoy work underwater all season, where they are gradually worn down by waves, current, corrosion and mud. Daivings.lv and “Dronelab” SIA divers install, inspect and repair mooring systems for yachts, boats, pontoons and floating docks throughout Latvia.
In this article, we explain what the mooring system consists of, why it should be checked regularly, and how divers perform this work.

What does the mooring system consist of?
Although the solution varies from place to place, most mooring systems consist of similar elements:
- Anchor or anchor block — a heavy concrete block, anchor, or anchor screwed into the ground that holds the entire system in place.
- Ground circuit — the heavy part of the chain that rests on the bearing and absorbs the load.
- Connections — shackles and swivels that connect the chain links and prevent them from tangling.
- Top chain and buoy — connects the system to the surface, a boat is tied to the buoy.
A system is only as strong as its weakest link, which is why it is not enough to just check what is visible above the water.
Our mooring system services
Installation of mooring buoys and anchors
We assess the depth of the location, the type of seabed, the size of the vessel and the typical wind and wave conditions. We then select the appropriate anchor or anchor block, chain length and connections, place them on the seabed and secure the buoy system. Installation in public waters may require coordination with the municipality or port authority, and we help you understand what is required in your case.
Anchoring of pontoons and floating walkways
Floating docks and pontoons must adapt to fluctuations in water levels while maintaining stability. We position anchors and chains so that the structure does not slip or sway too much, and then check the tension.

Annual inspection and maintenance
It is recommended to inspect the mooring system at least once a year — preferably before the start of the season. A diver checks the chain links for wear, corrosion, the condition and fastening of shackle pins, the mobility of swivel joints, and whether the anchor has moved. We prepare a photo report with recommendations for each location.
Repair and replacement under water
If we find worn or damaged elements during the inspection, we replace them on site — without having to haul the entire system ashore. It's faster and cheaper than a complete system rebuild.
Checking after the storm
A strong storm can move anchors, twist chains, or damage connections. After a storm, we check the system and restore it before the boat is left unattended again.
Why can't the mooring system be inspected from shore?
Most of the stress and wear occurs where the chain meets the bearing and joints. These areas are underwater and often in mud, so only a diver can assess them. One worn shackle pin or chain link is enough to cause a boat to break loose in a storm - with consequences for both the boat itself and those nearby.

How is the work going?
- Application. You specify the location, the size of the vessel, and what is known about the existing system.
- Survey. The diver assesses the bed, depth, and condition of existing features.
- Offer. We recommend a solution and calculate the cost of labor and materials.
- Work. We install, test, or repair the system using our motorboat.
- Report. We provide a photo report and recommendations for the next inspection.
We use our own for work. RIB motorboats, which allows you to quickly move between multiple moorings within a day.

Cost
The cost of team work is determined for a full working day — starting from 800 EUR. We can usually inspect or install several moorings in one day, so it is beneficial for yacht clubs and ports to order an inspection for several places at the same time. We calculate the costs of materials (anchors, chains, connections, buoys) separately.
Frequently asked questions
How often should the mooring system be inspected?
At least once a year, preferably before the season. Additionally, after strong storms or if you notice that the boat or buoy has moved.
Can you check out multiple locations at the yacht club in one day?
Yes. It is also the most cost-effective option, as the cost of a working day is divided between several locations.
Do you also work in the winter?
Yes, we can work with dry suits all year round if the body of water is not frozen or if it is possible to work safely from the ice.
Request a mooring system inspection or installation
- Phone / WhatsApp: 220-77-202
- E-mail: [email protected]
- In-store service: Installation and maintenance of mooring systems
The work is carried out by divers from “Dronelab” SIA. See also our other underwater work services.
