Buoyancy Compensator (BCD) Care: Rinsing, Storage, and Maintenance

The buoyancy compensator (BCD or jacket) is a piece of equipment that many divers just rinse off the outside and hang to dry after a dive. However, the most important part is inside: the air bag, the filling valve and the exhaust valves. This is where salt, chlorine and sand get trapped. Over time, they form crystals that damage the valves and cause leaks. An unmaintained BCD can suddenly start to leak air or inflate itself, which is a serious safety risk underwater.

In this article, Daivings.lv instructors explain how to properly care for your BCD after each dive, how to store it, and when professional maintenance is needed.

Why the inside of a BCD needs to be rinsed

During a dive, when air is released through the inflation hose or the exhaust valves, a small amount of water enters the BCD bag. After a dive in the sea, this is salt water, which, when dried, leaves salt crystals inside the bag and in the valve seals. As a result, the valves no longer close completely, the inflation button can get stuck, and the bag begins to gradually lose air.

How to Rinse a BCD After a Dive

Exterior and buckles

  • Rinse the entire jacket in fresh water, including straps, buckles, and fasteners.
  • Remove the weights from the scale pockets and rinse them separately, as sand accumulates there.
  • Press the fill and drain buttons several times under water and pull the drain valve cords.

BCD weight pocket and buckle, which should be rinsed after diving

Rinsing the inside of the bag step by step

  1. Release all air from the BCD.
  2. Hold the end of the filling hose upwards and, by pressing the release (mouth filling) button, pour approximately 1-2 liters of fresh water into the bag.
  3. Inflate the BCD with your mouth or with the inflation button if it is attached to the cylinder.
  4. Turn and shake the jacket so that the water rinses the entire inside of the bag.
  5. Turn the BCD upside down and drain the water through the fill hose by pressing the drain button. Then drain the remaining water through the bottom drain valve.
  6. Repeat 2-3 times, especially after diving into the sea or pool.

Drying and storage

  • After rinsing, inflate the BCD slightly and hang it in the shade on a wide hanger so that the inside dries and the bag does not stick together.
  • Do not dry or store your BCD in direct sunlight or in a hot car. UV radiation and heat will damage the fabric and glued seams.
  • For long-term storage, leave the BCD partially inflated in a cool, dry place.
  • Do not store with heavy objects on top and do not fold it into sharp creases.
  • Protect the filling hose connection from sand and dirt.

Check before each dive

Before diving, when the regulator is connected to the cylinder, check the BCD:

  • Press the inflation button. The BCD should inflate evenly and the button should not stick after being released.
  • Bleed air through the fill hose and each exhaust valve.
  • Inflate the jacket fully and listen for any air leaks.
  • Check that all buckles, weight pockets and cylinder straps are secured.

A simple at-home leak test is to fully inflate your BCD and leave it for a few hours. If it has become noticeably softer, there is a leak that should be checked by a service center.

Professional BCD maintenance

Manufacturers recommend that BCD maintenance be performed annually or according to the manufacturer's schedule, often in conjunction with annual maintenance of the regulatorDuring maintenance, the technician disassembles and cleans the fill valve, replaces O-rings and seals, checks the exhaust valves and pressure relief valve, and performs a leak test.

Diving equipment technician tools for BCD and regulator maintenance

Daivings.lv authorized equipment technician performs BCD maintenance and repair, as well as Aqualung and Apeks regulator serviceIt is recommended to do this at the end of the season or before it begins, when there are fewer lines at the service.

When is it time to change the BCD?

  • The bag loses air even after replacing the valves and seals.
  • The fabric is faded, stiff, or starting to crack.
  • Straps and buckles are worn or broken.
  • The BCD is no longer compatible with your equipment or diving style.

If you choose a new BCD, Daivings.lv store available, for example, Cressi Aquawing Plus and Cressi Aquawing Basic. Let us help you choose the right model, phone 220-77-202.